USB to TTL Serial Cable - Debug / Console Cable for Raspberry Pi

USB to TTL Serial Cable - Debug / Console Cable for Raspberry Pi
Beoordeling
5.0 / 5.0

Artikelnr.P954
MerkAdafruit
Model954
Voorraad
Nog ... stuks op voorraad
Vandaag voor 23:59 besteld, morgen in huis.
Verzonden vanaf  € 25 - United States
Verkocht per stuk
€ 13,55
In winkelwagen
  • Koop 10 stuks voor € 12,90 per stuk5% korting
  • Koop 25 stuks voor € 12,30 per stuk9% korting
  • Koop 50 stuks voor € 11,65 per stuk14% korting
  • Koop 100 stuks voor € 11,05 per stuk18% korting
  • Koop 500 stuks voor € 10,40 per stuk23% korting

Beschrijving

The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USB<->Serial conversion chip and at the end of the 36" cable are four wire - red power, black ground, white RX into USB port, and green TX out of the USB port. The power pin provides the 5V @ 500mA direct from the USB port and the RX/TX pins are 3.3V level for interfacing with the most common 3.3V logic level chipsets.

Because of the separated pin plugs, this cable is ideal for powering and connecting up to the debug/login console on the Raspberry Pi or BeagleBone Black. Connect the pins as shown to power the Pi or BBB and establish the RX/TX link.
  • If you are running Windows 7/8/10 etc, check this tutorial page with links to drivers for both PL2303 and CP2102
  • If you are running Mac OS X, check this tutorial page with links to drivers for both PL2303 and CP2012
  • If you are running Linux, drivers are already included in the kernel, no need to install anything!
Also handy for hacking WiFi routers to install alternate OS's, or nearly any other 3.3V logic serial port. This is easier to use than an FTDI cable in many cases because the wires are separated. Note that we call this a "TTL cable" (since that's what they're called) but technically it's CMOS logic.

This cable is not good for Arduino re-programming such as a Boarduino, MENTA, Monochron, etc. because it does not have the DTR/RTS wire necessary for initiating the bootloader reboot sequence. For that we suggest an FTDI cable or FTDI friend.

  There are four wires: red power, black ground, white RX into USB port, and green TX out of the USB port.
The power pin provides the 5V @ 500mA direct from the USB port and the RX/TX pins are 3.3V level for interfacing with the most common 3.3V logic level chipsets.
  • If you are running Windows 7/8/10 etc, check this tutorial page with links to drivers for both PL2303 and CP2102
  • If you are running Mac OS X, check this tutorial page with links to drivers for both PL2303 and CP2012
  • If you are running Linux, drivers are already included in the kernel, no need to install anything!
Revision History
  • Prior to July 1 2014 this cable would come with a PL2303HX chipset and a black USB body. After July 1, 2014 we changed to a violet body and the PL2303TA chipset. The new 'TA cables are Win8 compatible, and are more reliable especially when dealing with random USB-disconnects.
  • As of Dec. 21, 2016 we will be shipping cables with SiLabs CP2012 chipset instead of Prolific. SiLabs chips seem to have better driver stability, and can handle very high speeds and 'unusual' non-standard baud rates. Other than the driver installation, the cables perform identically.

Vraag en antwoord

Beoordelingen

Nederland
5 sterren
Goede en mooie kabel zit er netje en verzorgd uit
Geplaatst op 



Logo USB to TTL Serial Cable - Debug / Console Cable for Raspberry Pi
USB to TTL Serial Cable - Debug / Console Cable for Raspberry PiKlik op een ster om een beoordeling te geven